How can l configure a Cisco 815 cable interface to use 1 frequency only - testmy.net resource / tool
Home
Welcome, Guest. Please login or register.
Did you miss your activation email?

  



donations help testmy.net pay for the very high cost to run the site. Any amount is greatly appreciated.
Click to read why...

  spcr
    
News : uglystupid2 Don't look stupid, make sure you keep up-to-date with our rules, please read rules, click here  police July 05, 2008, 01:17:25 PM
testmy.net broadband community  |  Main Forum  |  HELP!  |  Networking and Hardware  |  Topic: How can l configure a Cisco 815 cable interface to use 1 frequency only Advanced search
  0 Members and 1 Guest are viewing this topic. « previous next »
Topic Tools Search this topic
 Pages 1 Go Down
Author
Topic: How can l configure a Cisco 815 cable interface to use 1 frequency only  (Read 702 times)
shome
Earning Trust
*
Offline Offline

Posts: 2



View Profile
« on: May 15, 2008, 07:42:43 AM »
Good day guys

l do use the Cisco Ubr 905 for my cable modem connections. and with it l can use this command
" cable-modem downstream frequency xxx000000 only " in the cable modem interface to make the Ubr scan and establish connection only with that frequency.
i.e
interface cable-modem0
 no cable-modem compliant bridge
 cable-modem boot admin 2
 cable-modem boot oper 5
 cable-modem downstream frequency 579000000 only
!

  But the Cisco Ubr 905 has been replaced with the Cisco 815 ISR router.
l noticed l cannot make this Cisco 815 cable modem interface establish connection only on 1 frequency.

l need your help

Much Regards sad
Logged
ladiasya
New Member
*
Offline Offline

Gender: Female
Posts: 7



View Profile
« Reply #1 on: May 22, 2008, 10:12:54 AM »
To change the channel of operation of the Router, select the desired channel from the drop-down menu and select your channel. Click "Apply Changes" to save the setting. You can also change the SSID. The SSID is the equivalent to the wireless network's name. You can make the SSID anything you want to. If there are other wireless networks in your area, you should give your wireless network a unique name. The default is Belkin_Pre-N_xxxxxx. To change the SSID, click inside of the SSID box and type in a new name. Click "Apply Changes" to make the change.
Logged
shome
Earning Trust
*
Offline Offline

Posts: 2



View Profile
« Reply #2 on: May 22, 2008, 11:07:38 AM »
Hello  ladiasya
Thanks for the response
 However, l am talking about a Cisco 815 Cable router.
   It had a Cable-Modem Interface
l want this interface to scan for one frequency when it comes up.
l am able to do that with the Cisco UBR 900 series making use of this command
 "cable-modem downstream frequency xxx000000 only"
This is a configuration done in the Cisco IOS.

My task is to achieve this with the Cisco 815 ISR Cable router.
 Hope am making a meaning of what l want sir
Please help, l will be grateful
Much Regards
peter Neutral
Logged
ladiasya
New Member
*
Offline Offline

Gender: Female
Posts: 7



View Profile
« Reply #3 on: May 22, 2008, 01:05:52 PM »
that particuar router should be programable same as the belkin
you know like linksys uses 192.168.1.1   and belkin uses 192.168.2.1...it's access to the settings to change the AUTOSEARCH channel  to a specific channel/ssid
Logged
ladiasya
New Member
*
Offline Offline

Gender: Female
Posts: 7



View Profile
« Reply #4 on: May 22, 2008, 01:16:30 PM »
http://www.cisco.com/en/US/docs/ios/12_4/12_4x/12_4_6xe/snwshoe1.html
Logged
ladiasya
New Member
*
Offline Offline

Gender: Female
Posts: 7



View Profile
« Reply #5 on: May 22, 2008, 01:21:29 PM »
The cable interface on the Cisco 815 has dedicated CPU and memory and is designed to adhere to the Embedded Cable Modem Module (ECMM) standard. For the Cisco uBR905, the DOCSIS® code ran completely within Cisco IOS Software. Therefore, with the Cisco uBR905, any change to the modem code required a change to the Cisco IOS Software image. With the Cisco 815, all the DOCSIS code resides on the cable modem daughter card itself and is run locally in the Broadcom chipset independently of Cisco IOS Software. This design allows the cable modem firmware to be upgraded independently of Cisco IOS Software
Logged
Print  Pages 1 Go Up
testmy.net broadband community  |  Main Forum  |  HELP!  |  Networking and Hardware  |  Topic: How can l configure a Cisco 815 cable interface to use 1 frequency only « previous next »
Jump to:  

 
    
testmy.net's forum is proudly Powered by SMF | SMF © 2006-2007, Simple Machines LLC
Bookmark: Del.icio.us    StumbleUpon
 		  

 

 © 1999-2008 testmy.net - Contact - Legal - Facts & FAQs
Page Loading Stats: This forum Page created in 0.086 seconds with 35 queries.